GE / Monogram Gas Grill Parts
Gas Grill Parts from BBQParts.com

We stock and sell selected replacement parts for GE / Monogram gas grill models.
All the parts we stock and sell for GE / Monogram gas grills are listed below.

Please order in the quantities you need.
 

Free Shipping For All Orders Over $99.00! (Low $12.98 Shipping Charge for Orders Less than $99.00)

Burners for GE / Monogram Grills Parts Description Price Stainless Steel ALFU1 Burner with Mounting Bracket P/N ALFU1-w/MB in-stock In recent years, there had been two different styles of ALFU1 burners sold. By ordering this one, you will receive a high quality, stainless steel ALFU1 burner with stabilizing bracket - this is a center feed, U shaped tube burner designed with a bracket on the underside of the burner. The stabilizing bracket has a mounting stud on the underside and a cotter pin to hold it securely in place. (the other burner for the Alfresco grills did not have a bracket). See the photos in this listing. This burner has an air shutter and flame crossover tube. The burner dimensions are 18 1/4 inches long by approximately 7 1/4 inches wide It is 7 1/4 inches wide at the bracket and 7 1/8 inches wide at the crossover tubes. The distance from the end of the burner at the venturi to the mounting stud under the bracket is 14 7/8 inches. We encourage customers to remove their current Alfresco burner and confirm the match and the measurements. Order the quantity you need. $72.00 Each Quantity: Cast Iron Burner [CIDCSLX] P/N 22701 in-stock This is a cast iron burner used in many 27, 36, and 48 inch GE / Monogram Grill Parts gas grills. Please match up from illustration and sizes. 22701 Burner dimensions: 16 inches from end to end - from the end of the cast iron venturi assembly to the opposite, squared off end of the burner. Burner is 6 1/4 inches wide. Burner comes with adjustable air shutter and screw. (CIDCSLX) This burner replaces GE/MONOGRAM OEM part number WB28X10025. $74.99 Each Quantity: (Limit: 25 burners per order.) Cast Iron Burners - 2 Pak P/N 22701-2pak in-stock By ordering this two pack of 22701 burners, you will receive two 22701 cast iron burners. These are cast iron burners used in many 27, 36, and 48 inch GE / Monogram Grill Parts gas grills. Please match up from illustration and sizes. 22701 Burner dimensions: 16 inches from end to end - from the end of the cast iron venturi assembly to the opposite, squared off end of the burner. Burner is 6 1/4 inches wide. Burner comes with adjustable air shutter and screw. (CIDCSLX-2pak) This burner replaces GE/MONOGRAM OEM part number WB28X10025. $149.98 for 2 Burners Quantity: (Limit: 25 burners per order.) Cast Iron Burners - 3 Pak P/N 22701-3pak in-stock By ordering this three pack of 22701 burners, you will receive three 22701 cast iron burners. These are cast iron burners used in many 27, 36, and 48 inch GE / Monogram Grill Parts gas grills. Please match up from illustration and sizes. 22701 Burner dimensions: 16 inches from end to end - from the end of the cast iron venturi assembly to the opposite, squared off end of the burner. Burner is 6 1/4 inches wide. Burner comes with adjustable air shutter and screw. (CIDCSLX-3pak) This burner replaces GE/MONOGRAM OEM part number WB28X10025. $224.97 for 3 Burners Quantity: (Limit: 25 burners per order.) Cast Iron Burner [Replaces OEM P/N 210348] [CIDCS-LG] P/N 23601 in-stock This is a cast iron burner used in some 36 inch and 48 inch models of DCS grills. Please match up from illustration and sizes. This burner replaces DCS part number 12012. 23601 Burner dimensions: 20 1/2 inches from end to end - from the end of the cast iron venturi assembly to the opposite, squared off end of the burner. Burner is 6 1/4 inches wide. Burner comes with adjustable air shutter and screw. (DCS-BBQ236) (CIDCS-LG) This part replaces DCS OEM part numbers 12012 and 210348. This burner replaces GE/MONOGRAM OEM part number WB28X10021. $94.99 Each Quantity: (Limit: 25 burners per order.) DCS Cast Iron Burners - 3 Pak [Replaces OEM P/N 210348] [CIDCS-LG] P/N 23601-3pak in-stock By ordering this three pack of 23601 burners, you will receive three 23601 cast iron burners These are cast iron burners used in some 36 inch and 48 inch models of DCS grills. Please match up from illustration and sizes. This burner replaces DCS part number 12012. 23601 Burner dimensions: 20 1/2 inches from end to end - from the end of the cast iron venturi assembly to the opposite, squared off end of the burner. Burner is 6 1/4 inches wide. Burner comes with adjustable air shutter and screw. (DCS-BBQ236) (CIDCS-LG) This part replaces DCS OEM part numbers 12012 and 210348. This burner replaces GE/MONOGRAM OEM part number WB28X10021. $284.97 for 3 Burners Quantity: (Limit: 25 burners per order.) DCS Stainless steel Smoker tube Burner [Replaces OEM P/N 213467] [DCST1] P/N 12181 in-stock This stainless steel tube burner is used for the smoker in a number of Dynamic Cooking System grills. The burner measures 18 inches long by one inch in diameter. When ordering and installing, check carefully that it matches the original burner in your grill. (MHP-DCST1) This smoker burner replaces GE/MONOGRAM OEM part numbers WB28X10103 and WB28X10007. This smoker burner replaces DCS OEM part number 213467. (DCST1) $21.25 Each Quantity: Igniter Components and Parts Parts Description Price Rotary Igniter With Knob, One Outlet [UP-5B] P/N 03200 in-stock This one outlet, rotary igniter is shipped with the knob included. (UP-5B). $9.89 Each Quantity: 20 inch Wire P/N IG7B in-stock This replacement 20 inch insulated wire is for use with most rotary and push button igniter systems. One end has a female spade connector and the other end has a female round connector. $4.89 Each Quantity: 20 inch Igniter Wire with Two Female Flat Spade Ends P/N IG18B in-stock 20 inch igniter wire with 2 female flat spade connector ends. $3.89 Each Quantity: Electrode, Bracket, and Wire Assembly [06020] P/N IG37B in-stock This electrode, bracket and wire assembly is found in number of grill brands, primarily DCS. The assembly is not used in all DCS models. Please choose carefully. The wire is 15 inches long and is attached to the electrode which is mounted under the bracket. Electrode tip extends into the collector box. Bracket measures 3 inches long and one inch wide. Please note: The connector end of this wire that connects to the igniter is ROUND (Not flat). (IG37B, 06020) $8.79 Each Quantity: Left Side Collector Box and Electrode [Replaces OEM P/N 214269 and WB02X10660] P/N IG39B in-stock This is a 'left' side collector box and electrode with an attached 15 inch molded wire. Fits some older Dynamic Cooking System models and some GE/Monogram models. Refer to OEM part numbers at end of this description. The assembly has a collector box for the 'left Side' with a 90 degree bend electrode tip that has a 2 1/2 long ceramic insulator and a 15 inch molded in wire that ends with a round connector fitting. Replaces DCS OEM part number 214269 and GE/Monogram OEM part number WB02X10660. Choose carefully. $29.50 Each Quantity: Right Side Collector Box and Electrode [Replaces OEM P/N 214268 and WB02X10659] P/N IG40B in-stock This is a 'right' side collector box and electrode with an attached 15 inch molded wire. Fits some older Dynamic Cooking System models that require a left and right side collector box and some GE/Monogram models. Refer to OEM part numbers at end of this description. The assembly has a collector box for the 'right Side' with a 90 degree bend electrode tip that has a 2 1/2 long ceramic insulator and a 15 inch molded in wire that ends with a round connector fitting. Replaces DCS OEM part number 214268 and GE/Monogram OEM part number WB02X10659. Choose carefully. $28.50 Each Quantity: Spark Generator and Push Button [Replaces OEM P/N 212334P] [03360] P/N IGEIB12B in-stock This electronic spark generator and push button assembly has 9V battery terminals mounted on the side. There are six output terminals. There are two input terminals for push button on the back. This is a replacement part for DCS OEM part number 212334P. (IGEIB12B, 03360) $39.50 Each Quantity: Igniter Push Button [Push button only] P/N IGEIB18PB in-stock This is an igniter push button (PUSH BUTTON ONLY) for use with two igniter modules we stock and sell: IGEIB12B and IGEIB14B. The push button is used to trigger battery module to spark electrodes connected to it. $14.99 Each Quantity: Knobs Parts Description Price Universal Gas Grill Control Knob. P/N 02342 in-stock Universal Knob. Selectable D Position, Socket Dia. (6mm Or 8mm), And Shaft Length (Flush, 0.25 Inch, Or 1.625”. Shatfs Can Also Be Trimmed To Desired Length). Includes Six Inserts (Shafts) And Set Screw. Fits Any Grill With Inside Bezel Dia. Greater Than 2.1875. $13.89 Each Quantity: Rotary Igniter Knob P/N GGK9 in-stock This is the replacement Knob only that is used on rotary igniters, igniters that are manually turned by hand to produce a spark. The Knob is 1 and 3/4 inches in diameter. Directional arrows are molded in the plastic facing of the Knob. (20182601, 20173101) $3.95 Each Quantity: Stainless Steel Cook Grids Parts Description Price Stainless Steel ROD Cooking Grid for DCS Grills [Replaces OEM P/N 212408P] P/N CG79SS4 in-stock Made in the USA. This newly manufactured cook grid is made of 304 stainless steel rod that is 5/16 inches in diameter and designed and made specifically for Dynamic Cooking System gas grills. Each cook grid measures 10 7/16 by 20 1/2 inches. Sold individually. Please order the quantity you need. This CG79SS4 grid is notched on all four corners. This part replaces DCS OEM part number 212408P. This cook grid, CG79SS4, replaces GE/MONOGRAM OEM part number WB49X10013. $87.99 Each Quantity: Three Piece Cook Grid Set Made of Stainless Steel ROD for DCS Grills [Replaces OEM P/N 212408P] P/N CG79SS4-3pak in-stock Made in the USA. This newly manufactured cook grid set is made of 304 stainless steel rod. Each grid is 5/16 inches in diameter and designed and made specifically for Dynamic Cooking System gas grills. Each cook grid measures 10 7/16 by 20 1/2 inches. Sold here as a set of 3. This CG79SS4 grid is notched on all four corners. This part replaces DCS OEM part number 212408P. This cook grid, CG79SS4, replaces GE/MONOGRAM OEM part number WB49X10013. $263.97 Set of 3 Quantity: Stainless Steel ROD Cook Grid for DCS Grills [Replaces OEM P/N 212427P] P/N CG80SS in-stock Closeout Pricing. While Quantities Last. Made in the USA. This newly manufactured cook grid is made of 304 stainless steel rod that is 5/16 inches in diameter and designed and made specifically for Dynamic Cooking Systems gas grills. Each cook measures 12 3/4 inches by 19 1/2 inches. Sold individually. Please order the quantity you need. Replaces DCS OEM part number 212427P. $87.00 Each Quantity: Two Piece Cook Grid Set Made of Stainless Steel Rod. P/N CG109SS-2 in-stock This high quality stainless steel cook grid set is made of 5/16 inch thick stainless steel rod. Each cook grid measures 18 1/2 inches from front to back and 12 3/4 inches across of the front. The combined dimensions of the two grids side by side is 25 1/2 inches across the front and 18 1/2 inches front to back. The set is designed to replace two individual DCS original equipment porcelain coated cook grids that are part number 212425. $148.00 Set of 2 Quantity: Heat Plates and Briquettes Parts Description Price Heat Plate for DCS 27 inch model [Replaces OEM P/N 213948] [DCSHP2] P/N 90271 in-stock Stainless Steel Heat Plate. Dimensions 10 1/2 inches by 16 1/2 inches. Sold Individually. Used in sets of 2. This heat plate fits many of the 27 inch models. Please verify your selection by comparing to the heat plate in your DCS and verifying measurements. (DCSHP2) The part replaces DCS OEM part numbers 213948 and 30709-020. This heat plate replaces GE/MONOGRAM OEM part number WB02X10434. $39.00 Each Quantity: Heat Plates for the following DCS Models: 24 inch, 36 inch, 48 inch wide [Replaces OEM P/N 213949] [DCSHP1] P/N 90361 in-stock Stainless Steel Heat Plate. Dimensions - 9 9/16 by 19 inches. Sold Individually. Used in sets of 2, 3 or 4. This heat plate replaces DCS part number 30522. This heat plate fits many of the 24, 36, and 48 inch models. Please verify your selection by comparing to your DCS heat plate and checking measurements. (DCSHP1) This part replaces DCS OEM part number 213949. This heat plate replaces GE/MONOGRAM OEM part number WB02X10384. $58.99 Each Quantity: Stainless Steel Heat Plate [Replaces OEM P/N 80006] [LYNXHP1] P/N 92571 in-stock This stainless steel heat plate measures 17 inches by 9 11/16 inches. Order the quantity you need. Our heat plate does not include briquette clips. Sorry, we do not stock or sell them. (LYNXHP1) This part replaces Lynx OEM part number 80006. This heat plate replaces GE/MONOGRAM OEM part number WB02X10698. $59.00 Each Quantity: USA-MADE Square Ceramic Briquettes. 28 Briquettes per box. P/N BBQLYX-USA in-stock These high-quality, Made in the USA, briquettes are manufactured for us by the leading manufacturer/supplier to a number of high quality, American made brands of gas grills. They fit and work for heat plates in Lynx, Dynasty, and Alfresco gas grills. Can be used in other brands as well. They are a light brown, earth tone color (same as ones used in high end, USA grills) and the same size as the white replacement briquettes sold on the internet. The briquettes are well packaged, in individual boxes of 28 briquettes. They are NOT shipped in bags. The briquettes measure 2 inches square and are 3/4 inch tall. The four sides meet at a flat top - like a cut off pyramid. On the bottom, there is a round recess, approximately 1 inch in diameter, to capture and transfer heat better. We are able to offer these at very reasonable pricing because of our quantity buying. By ordering one box, you will receive one box of 28 briquettes. Order the box quantity you need. The number of briquettes you need depends on the size of the heat plate, and the number of heat plates in your grill. We suggest you count before ordering to get enough. (28 briquettes per box). Highly recommended. (not 41648) $34.95 Box of 28 briquettes Quantity: